The saw blade producer, Håkansson Sågblad AB, patented in the U.S. a new blade profiledesigned specially to cut fish and meat. The most important advantage of that blade is that its teethare not set, therefore the material lost when cutting is really smaller. The special geometry of thatprofile made that nobody had found a proper way to produce it before.The goal of the outlined work is to develop a machine to produce these new blades in afeasible way.The research approach of the project can roughly be divided into three phases:1.- Invention and development of a proper distribution of blades to produce a big amount ofthem at the same time.2.- Research of the best production process to produce the blades.3.- Main design of the machine to produce the blades.In the Thesis these three points are carefully developed and studied in the form of the startpoint of a really bigger project. Some tests had been done in order to prove all the analytical ideasand the results obtained had been satisfactory enough to give Håkansson the start point of a bigbusiness.

This study presents a methodology that enables the annual average power of a wind turbine to be increased by automatically optimizing it?s airfoil, twist and chord dis- tribution. As a part of the study the software SiteOpt has been developed. This software connects the open source software XFOIL with the blade element momen- tum theory. XFOIL gives lift and drag coefficients which enable the blade element momentum theory to predict the power of a wind turbine at different wind and ro- tational speeds.

This Master Thesis has been carried out as a new product development project in collaborationwith G-Man Tools AB located in Edsbyn. The purpose of the project was to construct a newpruning saw there the blade is integrateble in the handle, thus a foldable pruning saw.The work has been performed on the occasion of G-Man Tools AB wanted to improve theirproduct range by creating a saw that complement their range of quality saws. They have a similarproduct today, but they do not manufacture this product by them selves and it is not directlytargeted against garden use, which is a disadvantage when it is one of their major markets.Even though almost the entire chain from the requirements of the users to drawings has beentaken into consideration, emphasizes has been put on generating ideas. However the first thingthat was carried out was to establish a productspecifikation from interviews with users and thecompany?s experience.

The thesis project is accomplished during winter and spring 2008 at Karlstad University at the faculty of technology and science. The tutor at Karlstad University is Nils Hallbäck and the examiner is Hans Johansson. Rolls-Royce at Kristinehamn in Sweden is the initiator for the project. The thesis project title is design of the blade bolt joint on Kamewa CPP. CPP stands for controllable pitch propeller.

Scana-Booforge is a Swedish company which specialize in heat treatment of various metal. The treatments take place in quenching ovens, where fans are used to circulate the hot air. The fans used today do not have a satisfactory lifespan. This thesis aims to develop a new design of the fans for the quenching ovens, and the goal is that the new fans will bring cost savings for Scana-Booforge.The design development process started with mapping out the environment in which the fans operate, and with analysis of the existing fan structure and damages, in order to establish the cause of failure and of short durability. The performance of the fan were also established at this stage.

This rapport handles the presence of two kinds of watermills in the Swedish landscape. The first is a small type with a horizontal shovel blade and the other a bigger kind with a vertical standing shovel scoop. The rapport seeks for information of their capacity and how long they existed as flour producing units. A important issue is how small can a brook be and still run a mill. Finally the reasons for their disappearance in one selected parish is shown..

This thesis is based upon the work done at Westinghouse electric company (WEC)inVästerås during the spring semester of 2015 and describes the development of a quickcoupler with associated blade changing tool. These are meant to be used togetherwith a sawing tool that the company uses for the dismantling of nuclear reactors,which is performed under water.The aim of the thesis was to develop a complete manufacturing documentation withdrawings and related CAD models which Westinghouse later can use to manufacturethe tool and the quick coupler. It was also included in the assignment to, if necessary,modify parts of the saw tool to adapt these to the intended blade changing tool.A number of visits to the company's workshop was made during the time to study thesaw that the thesis is based upon. The purpose of these visits was to get a better ideaof the dimensions, construction and the field of use of the saw. On three of thoseoccasions various engineers and consultants accompanied us to discuss possibleproblems with different ideas.This was interspersed with information in the form of literature studies on quickcouplers to create a clearer picture of the nature of the task.When enough information had been gathered a functional analysis was made to dividethe main problem into subthis phase the idea and concept generating process took place.The methods used for this was mainly brain writing and brainstorming.

The big change is a project where I created patterns on fabric. It is a collaborative project with Lotta Niemi. She studied fashion and textile designers and tailors from the Swedish School of Textiles in Borås and University of Technology in Sydney. The collaboration was to create designs on fabric for her upcoming clothing line for women, Fall / Winter 2013. The clothes will be sold online, in stores in Sweden and Japan.For Lotta Niemi?s clothing line, I wanted to create exclusive designs, rich patterns that worked out handmade and digital.

The expansion of the Swedish hydro power has contributed positively to the reduction of the environmental impacts from the fossil fueled power production. In the same time the extensive expansion has been proved to cause negative ecological and local environment impacts of a stream. This, in turn, has been affecting the biodiversity and fish stock negatively, which has been reduced. One of the underlying problems is the lack of possibility for the fish to pass the plants, but it is also directly correlated to the mortality rate of the fish passing through the turbine, which this study is investigating.The mortality rate has been computed for three different locations in Sweden, Untra, Tännfallet and a third one whose location is confidential, and is denoted as Case 1, 2 and 3. The model used to calculate the mortality rate in this investigation is based by existing blade strike models and knowledge and are investigating the death due to mechanical injuries from collision with a runner blade in the turbine.

This thesis describes teh solution of two problems regarding safety on powered lawnmowers; protectning the users from injury when using the lawnmower in slopes, and when cleaning the cutting blade.The task was carried out through initial studies on a representative lawnmower. A generation of ideas followed with an evaluation to select the best solution. The winning concept was further developed to reach acceptable performance. The word resulted in a functioning prototype utilising an original way of detecting inclinations without incorrect signals. It c an serve as a platform for further development into a product.The work gives insightful experience of solving real-world problems, and especially to deal with situations where several variables and their effects are unknownPlease note that several parts of the work are confidential, and have therefore been removed from the thesis..

This paper deals with knives excavated in the Birka Garrison between 1997 and 2004, in a selection of 100 knives out of approximately 400. The aim is to measure and analyze the material to find out if certain elements in design points to a specific craft. Two groups of knifeblades can be seen, one with a convex bevel and one with a flat bevel of the blade. Considering osteological evidence, historical sources, and the main suitabillity of the knives, it is concluded that some of the flat beveled knives may have been used for crafting leather and fur, whereas the convex beveled knives are of an allround type..

This report looks at the possibility of designing a universal adapter for Flat Blade windshield wipers in cooperation with European Automotive Supplier AB.To understand and see if this is possible, a research and an extensive patent search where done. Then to add structure to the project a Ganttschematic were developed. To generate good and solid ideas, different methods for product development were looked upon.When a method was chosen and applied, a series of concepts emerged. Now the focus was to design and construct all the pieces. The desired manufacture procedures were looked upon as well as materials.

The purpose of this report is to survey Swedex AB?s production costs and to gather all info into a manageable calculation tool. This was made by time and motion studies, interviews of the personnel. All factors were gathered into an Excel chart.The calculation was made according to an additional-charge-method that was considered to satisfy Swedex AB?s goal.

This report shows the process of the development of a sensor module for the seed drills of Väderstad Verken AB. The module is supposed to replace existing solutions, provided that it is better from both a constructional- and an economical aspect. The purpose of the sensor is to continuously give the driver information about the level of height of the front- and drilling tools and the main purpose of the sensor is to allow the seeds to be placed at the desired depth. The sensors which have been taken into consideration have all been of an analogue type and have a protection class of minimum IP67.The methods applied have been taken from the book ?The Mechanical Design Process? by David G.

The Goal with this Master of Science thesis is to expand the possible turbine efficiencymeasurements on an exhaust turbocharger. It was done as a part of the CICERO competencecentre. To feed the turbine with air a special flow rig has been used. Instead of loading theturbine by just restricting the compressor flow a docking system for an electrical dynamometer isdesigned to use the dynamometer as an additional loading source. By using an electricaldynamometer as loading device for the turbine, measurements are not depending on compressorperformance.A large part of the work consists in designing accessories for the dynamometer.